ACCESSORIES FOR SERVO DRIVES

Double Servo arm (24 spline teeth, 64mm)

• aluminium
• 24 splined teeth
• length: 64mm

Double Servo arm (25 spline teeth, 64mm)

• aluminium
• 25 splined teeth
• length: 64mm

Hub shaft (24 teeth, 10mm diameter, 33mm length)

The hub shaft is an integral part of the ServoBlock. The long neck supports a 10mm heavy duty rack. The tabletop with an outer diameter of 32 mm can work with 32 mm clamps as well as 32 mm bearings. The pattern includes both through holes and tapped holes to make it compatible with almost every part of goBild.

Hub shaft (25 teeth, 10mm diameter, 33mm length)

The hub shaft is an integral part of the ServoBlock. The long neck supports a 10mm heavy duty rack. The tabletop with an outer diameter of 32 mm can work with 32 mm clamps as well as 32 mm bearings. The pattern includes both through holes and tapped holes to make it compatible with almost every part of goBild.

Light Servo Hub (24 teeth, 32mm diameter)

This 24-tooth servo hub is a sleek and slim corner that allows you to attach almost any 16mm pattern part to the top of the servo. The 14mm projection acts as a centering mechanism for mating pieces that have a 14mm hole.

Light Servo Hub (25 teeth, 32mm diameter)

This 24-tooth servo hub is a sleek and slim corner that allows you to attach almost any 16mm pattern part to the top of the servo. The 14mm projection acts as a centering mechanism for mating pieces that have a 14mm hole.

Servo fitting to the shaft coupler (splines 24 teeth to 6mm round hole)

This coupler allows a 6 mm diameter shaft to be fitted in line with the servo output key. The clamping function ensures that the shaft will not slip and be damaged, which means that it can be installed and removed repeatedly.

Servo fitting to the shaft coupler (splines 25 teeth to 6mm round hole)

This coupler allows a 6 mm diameter shaft to be fitted in line with the servo output key. The clamping function ensures that the shaft will not slip and be damaged, which means that it can be installed and removed repeatedly.

Servo gear (24 spline teeth, 12 teeth)

This 12-tooth servo gearbox is most commonly used to drive a 108-tooth hub, 48mm apart, for an enormous 9: 1 gear ratio.

For a more compact setup, it also works with a 48-tooth hub gear set 24mm apart for a 4: 1 ratio.

• Material: Brass
• Number of teeth: 12
• Pressure angle: 20 degrees

Servo gear (24 spline teeth, 15 teeth)

This 15-tooth servo gearbox is most commonly used to drive a 105-tooth hub, 48mm apart, for an enormous 7:1 gear ratio.

This gear reduction will increase the torque on the gear of the hub to 7 times that produced by the servo. The sacrifice will be to reduce the range of motion and speed by a ratio.

Servo gear (24 spline teeth, 20 teeth)

This 20-tooth servo gearbox is most commonly used to drive a 100-tooth hub, 48mm apart, for an enormous 5:1 gear ratio.

This gear reduction will increase the torque on the gear of the hub to 5 times that produced by the servo. The sacrifice will be to reduce the range of motion and speed by a ratio.

Servo gear (24 spline teeth, 24 teeth)

This 24-tooth servo gearbox is most commonly used to drive a 96-tooth hub, 48mm apart, for an enormous 4:1 gear ratio.

This gear reduction will increase the torque on the gear of the hub to 4 times that produced by the servo. The sacrifice will be to reduce the range of motion and speed by a ratio.

Servo gear (24 spline teeth, 30 teeth)

This 30-tooth servo gearbox is most commonly used to drive a 90-tooth hub, 48mm apart, for an enormous 3:1 gear ratio.

This gear reduction will increase the torque on the gear of the hub to 3 times that produced by the servo. This gear can also be used to drive a 30-tooth gear 24 mm away for a 1:1 ratio.

Servo gear (24 spline teeth, 40 teeth)

This 40-tooth servo gearbox is most commonly used to drive a 80-tooth hub, 48mm apart, for an enormous 2:1 gear ratio.

This gear reduction will increase the torque on the gear of the hub to 2 times that produced by the servo. Ta przekładnia może być również używana do napędzania 20 zębatego koła zębatego oddalonego o 24 mm dla przełożenia 2:1.

Servo gear (25 spline teeth, 12 teeth)

This 12-tooth servo gearbox is most commonly used to drive a 108-tooth hub, 48mm apart, for an enormous 9:1 gear ratio.

This gearbox can also be used to drive a 48-tooth gear 24 mm away for a 14:1 ratio.

Servo gear (25 spline teeth, 15 teeth)

This 15-tooth servo gearbox is most commonly used to drive a 105-tooth hub, 48mm apart, for an enormous 7:1 gear ratio.

This gear reduction will increase the torque on the gear of the hub to 7 times that produced by the servo. The sacrifice will be to reduce the range of motion and speed by a ratio.

Servo gear (25 spline teeth, 20 teeth)

This 20-tooth servo gearbox is most commonly used to drive a 100-tooth hub, 48mm apart, for an enormous 5:1 gear ratio.

This gear reduction will increase the torque on the gear of the hub to 5 times that produced by the servo. The sacrifice will be to reduce the range of motion and speed by a ratio.

Servo gear (25 spline teeth, 24 teeth)

This 24-tooth servo gearbox is most commonly used to drive a 96-tooth hub, 48mm apart, for an enormous 4:1 gear ratio.

This gear reduction will increase the torque on the gear of the hub to 4 times that produced by the servo. The sacrifice will be to reduce the range of motion and speed by a ratio.

Servo gear (25 spline teeth, 30 teeth)

This 30-tooth servo gearbox is most commonly used to drive a 90-tooth hub, 48mm apart, for an enormous 3:1 gear ratio.

This gear reduction will increase the torque on the gear of the hub to 3 times that produced by the servo. This gear can also be used to drive a 30-tooth gear 24 mm away for a 1:1 ratio.

Servo gear (25 spline teeth, 40 teeth)

This 40-tooth servo gearbox is most commonly used to drive a 80-tooth hub, 48mm apart, for an enormous 2:1 gear ratio.

This gear reduction will increase the torque on the gear of the hub to 2 times that produced by the servo. Ta przekładnia może być również używana do napędzania 20 zębatego koła zębatego oddalonego o 24 mm dla przełożenia 2:1.

Servo hub (24 teeth, 32mm diameter)

The 1908 series hub is 32mm in diameter and 6mm thick, allowing it to be supported with a bearing or clamped around it with a 32mm ID clamp. It includes both threaded holes and 16mm through holes, so you can attach almost any goBILDA® component to the top. The counterbore upper part will countersink the servo screw below the surface to keep it from interfering with the mating parts.

Servo hub (25 teeth, 32mm diameter)

The 1908 series hub is 32mm in diameter and 6mm thick, allowing it to be supported with a bearing or clamped around it with a 32mm ID clamp. It includes both threaded holes and 16mm through holes, so you can attach almost any goBILDA® component to the top. The counterbore upper part will countersink the servo screw below the surface to keep it from interfering with the mating parts.

Servo shaft (24 teeth, 10mm diameter, 36mm length)

Attaching a round shaft to a spline opens up many possibilities. The shaft is able to slide through a 10mm bearing, so it can be used in applications that would otherwise place a large radial load on the servo. To attach components to the shaft, use a 10mm clamping hub. This provides height adjustment as well as easy clocking of the mating part.

Servo shaft (25 teeth, 10mm diameter, 36mm length)

Attaching a round shaft to a spline opens up many possibilities. The shaft is able to slide through a 10mm bearing, so it can be used in applications that would otherwise place a large radial load on the servo. To attach components to the shaft, use a 10mm clamping hub. This provides height adjustment as well as easy clocking of the mating part.

Single Servo arm (24 spline teeth, 32mm)

Control the elevator, flap, lever, or pusher with this 24-tooth servo. The holes are evenly spaced 8 mm apart to align with any beams or mesh-based features.

• aluminium 
• 24 splined teeth
• length: 32mm